Chip Carving: Ultimate Guides for Beginners

May 23rd, 2019 | By | Posted in Best wood carving tools |

Chip Carving: Ultimate Guides for Beginners

To improve your chip carving skills, it is important to learn from the best. As a matter of fact, here are some of the best chip carving resources you can find online. Of course, the easiest way to transfer a pattern to wood is by gluing it directly on your material using a spray of wood glue. Be careful not to spray too much wood glue as it may later become a problem. A good way to remove the design from your wood when you are finished is to leave it in lukewarm water for a few minutes.

Common Mistakes on Chip Carving

Plunge Cut – Start by piercing straight down into the wood with the point of your primary knife at a 65-degree angle. Once the point of your knife reaches the desired depth, slide the blade out of the work piece.

Just push down towards the bottom left corner of the square. The second position is simply facing the blade away from you and pushing the tip of your blade into the wood with your thumb on the back of the knife. For all you out there with the need to learn a new hobby, look no further. Chip carving has been one of the most relaxing hobbies that I do, besides fishing of course. It isn’t super expensive to start out and with enough practice you can make great gifts for people.

Given these basic conditions, the technique is just waiting to be found. Sit long enough with a piece of wood and a sharp knife, and you might very well invent some form of chip carving. If you’ve ever carved your initials or an image into a wooden surface, congratulations—you are, in effect, a chip carver. When only two knives are used, give yourself every advantage by acquiring quality tools (see photo 3). The Premier knives shown here were designed by myself and are the result of many years of study and experience.

detail knife

Jerry has a unique way of finishing that really makes the colors stand out but still lets the wood grain show through. The face, hat and beard are painted with a very diluted acrylic paint After this is dry (a hair dryer comes in handy), it is coated heavily with boiled linseed oil. Let it drip off and wipe it dry with a paper towel. Then it is sprayed with a light coat of Deft or lacquer and then with a heavy coat.

Examples of this can be seen in the elaborate decorative carvings on pulpits, choir stalls, alters and other church fixtures. The wood carvers had become experts in their field and the carvings continued to become more and more elaborate. At this point, the art had made an 180-degree turn and now the stone carvers were trying to imitate the wood carvers. Even today, the architecture of the Gothic period serves as an almost limitless bank of ideas for the modern chip carver. Sharpening chip carving tools differs slightly than sharpening regular whittling knives.

Two Cherries Long Chip Knife

The properties of wood offered a medium in which intricate designs and patterns could be carved quickly. This was something that could not be done in stone.

  • Chip Carving Set from Flexcut® includes everything you need to create intricate geometric or freestyle patterns!
  • Through positive and negative space it is possible to take one chip carving design and create a multitude of patterns.
  • This is achieved by holding the blade just a couple degrees off the medium stone when sharpening (see photo 5).
  • The triangles can be long narrow shapes or very short and fat in appearance, even curves are included within the triangles outlines.
  • Here you will learn everything about this hobby to get you started the right way.
  • So while I was teaching Pat, I started a candle holder myself.

Carnelian Oval Carving Briolettes,Natural Gemstone Beads,Semi Precious Stone, Hand Carved Stones,8 inches,Size 11-20mm.

You can easily download chip grids online to use as tracing paper or a general guideline when chip carving. Those graph papers come in 1/4” and 1/3” grid patterns. You will need to draw your pattern on those chip carving graph paper before gluing it or tracing to your material. Many design patterns already come in graph paper size. They are more convenient to use, as long as you find a pattern that appeals to you.

Remember that there are three chip carving tools and each has their own particular use. This is most of the time due to your chip carving knives not being sharpened enough.

If this is your first chip carving knife, go with the Flexcut set as it is an all inclusive kit that will help you get started with chip carving right away. The only tools necessary for chip carving with a gouge are a compass to draw the circles, a long handled # 9-5mm wide gouge, a mallet and a piece of wood to carve. When I teach I encourage the students to draw several patterns on paper. They can copy their patterns by turning their compass to the same size as their pattern.

Put the tip of you blade into the first intersection of lines and press down coming towards you. You want to make sure that the blade of the knife is going in at about a 45° angle into the wood.

Chip carving has become for the woodworker an art form complete in itself. This technique uses triangular shaped cuts that create intricate and intriguing designs dancing across the surface of the wood. Just wanted to say what a great job you’re doing in the name of chip carving.

Lastly, as far as sharpening goes, complete with a leather strop and honing compound. Be sure to hone the blade to the tip as this is to remove any small chips, a magnifying glass is helpful in this situation to be able to see if there are any left.

She illustrates you the world of chip carving in very simple terms and newbies will have no problem following this guide, all the way to carving more complex patterns. This 144 pages paperback book has over 200 practice projects like making geometric shapes and free-form designs to can use to get better at chip carving. At the beginning of the Gothic period, the interior decorations in cathedrals were done almost completely in stone. The wood carvers imitated the carvings which had been done in stone. As time went on, the wood carvers realized that they were not as limited in what they could do as the stone masons were.

A Joiner’s Tool Kit

When this is dry, cover with watco wax, two parts light and one part dark. This needs to dry over night and then it can be buffed. When I go into a project, I know it is being made for someone special and I don’t let myself get personally attached to the carving. I still give it my best efforts, but it’s not so hard to let it go. Some carvers don’t have any problem that way and that is good.

Be Sociable, Share!

Leave a comment

All fields are required.

Need Prompt Service? Call Us Now!